10PCS Dodge Ram 1500 Front Suspension Kit - Ball Joints, Tie Rods, Sway Bar, Wheel Bearings & Hub

Description

1.Fit For: 2002-2005 Dodge Ram 1500 2.Package Includes: 2x Front Wheel Hub Bearing -513208 2x Front Sway Bar End Link -K80501 2x Rear Sway Bar End Link -K80425 2x Front Lower Ball Joint -K500153 1x Front Lower Control Arm - Passenger Side -K640446 1x Front Lower Control Arm - Driver Side -K640447 3.Note Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts. 1 Year Warranty Please check above compatibility list to make sure it fits your vehicle. Ball Joint Cfspeed-autoparts 10PCS Front Ball Joints Tie Rod Sway Bar Wheel Bearning Hub For Dodge Ram 1500 1.Fit For: 2002-2005 Dodge Ram 1500 2.Package Includes: 2x Front Wheel Hub Bearing -513208 2x Front Sway Bar End Link -K80501 2x Rear Sway Bar End Link -K80425 2x Front Lower Ball Joint -K500153 1x Front Lower Control Arm - Passenger Side -K640446 1x Front Lower Control Arm - Driver Side -K640447 3.Note Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts. 1 Year Warranty Please check above compatibility list to make sure it fits your vehicle. Ball Joint Ball joints may be grouped into two classifications, load carrying and non-load carrying. Ball joints may be manufactured with forged, stamped, cold-formed, or screw-machined housings. The coil spring is seated on the control arm to which the load-carrying ball joint is attached. For example, when the coil spring is mounted between the lower control arm and the chassis, the lower ball joint is a load-carrying joint. In a torsion bar suspension, the load-carrying ball joint is mounted on the control arm to which the torsion bar is attached. A load-carrying ball joint supports the vehicle weight. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Frequently Asked Questions (1).How will I know that I have to renew my ball joint parts? Or replace them? If your ball joint fails, you will listen to a strange sound while driving. And that sound may help you to realize that your ball joint has failed and you have to renew them. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).Are worn ball joints dangerous? Yes, it can be quite dangerous. Because, a worn ball joint causes suspension damage, inspection failure, and breakage of related parts. It might make your front suspension come apart while driving, so the wheels move in whatever direction inertia takes them. That can lead to a fatal accident. (4).What happens if I don't replace ball joints? If you don't want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (5).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. Item Specifics Brand cfspeed-autoparts Manufacturer Part Number C84134801CPS Interchange Part Number 515072,K7411,K7424,ES3538,K7422 OE/OEM Part Number Suspension arm Kit,replacing control arm car,rods ends Superseded Part Number car tie rod replacement Manufacturer Warranty 10 Year Placement on Vehicle Front Lower Upper Outer Type Control Arm & Ball Joint Assembly Universal Fitment No Features Greasable Items Included Mounting Hardware Performance Part No Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On Finish Coated Bolt Circle Diameter 5.5In. Payment Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay. Shipping Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries. All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days. We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if it is different from the one in eBay. The tracking number will be given for the customer to check the shipping status online (registered or faster service only). We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout. Returns MoneyBackOrExchange We stand behind every product we sell. All of our brand new items come with a 30-Days money-back guarantee. We define the item as defective only if it doesn't function as described. It is the buyer's responsibility to understand the item description before bidding. Contact Us We are dedicated to provide high quality products and satisfied customer service to our sincerely customers, so if there's any questions or problems with our products or service, feel free to contact us please. Cfspeed-autoparts DESCRIPTION PAYMENT SHIPPING RETURN POLICY CONTACT US Shop Category Store Home Suspension Parts ◈ Air Strut Assembly ◈ Air Spring ◈ Air Suspension Compressor ◈ Solenoid Valve Block ◈ Truck & Trailer Springs Truck & Trailer Springs Vehicles ◈ Audi ◈ Bentley ◈ BMW ◈ Buick ◈ Cadillac ◈ Chevrolet ◈ Citroen ◈ Dodge ◈ Ford ◈ GMC ◈ Hyundai ◈ Infiniti ◈ Isuzu ◈ Jaguar ◈ Jeep ◈ Land Rover ◈ Lexus ◈ Lincoln ◈ Mercedes-Benz ◈ Mercury ◈ Oldsmobile ◈ Porsche ◈ Saab ◈ Toyota ◈ Volkswagen Suspension Kits Air suspension valves solenoid Shocks & Struts Struts & Suspension Kit & Hubs coilovers complete strut Brake System Parts ◈ Brake Calipers ◈ Brake Drums & Brake Shoes ◈ Brake Pads & Brake Shoes Lift Supports Bumper Assembly Steering Knuckle Mass Air Flow Sensor Strut Mount air dryer Power Brake Booster trim tilt motor Removal Tool Control Arm Camber Arm dipstick Cylinder Piston Kit snorkel air intake Ballast Module Horns & Sirens Mud Flaps Protection Shield & Lift Kit Coil Springs Clock Spring Radius Arm Other Hot Item For 2011-2016 Hyundai Elantra Front Struts Tie Rods Sway Bar Suspension Kits USD 180.72 For Chevy Silverado GMC Sierra 1500 Front Struts Control Arm Ball Joint Tie Rod USD 245.77 Pair Front Left and Right Shock Strut Assembly For Chevrolet Equinox GMC Terrain USD 61.95 Rear Pair Air Suspension Air Spring For Lincoln Town Car Mercury Grand Marquis USD 66.58 For 07-2012 Nissan Versa Front Struts Lower Control Arm Tierod Sway Bars 10pcs USD 163.07 Picture New List Item Brake Shoes Front Rear For Honda Rancher 350 Rancher 400 Foreman 400 Foreman 450 USD 22.29 Rear 2x Air Suspension Shock Strut For Jeep Grand Cherokee /Dodge Durango 11-15 USD 98.33 For 10 11 12 13 14 Toyota Hilux Vigo Car Mud Flaps Splash Guard Fender Mudguards USD 34.54 Carbon Fiber Brake Pads Kit Front FA69 3 For 90-00 Honda GL1500SE Goldwing 1500 USD 16.79 Front Brake Pads + Rear Brake Shoes For 03-07 Suzuki LTA400F 4x4 Auto Eiger 400 USD 24.98 Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us 10PCS Front Ball Joints Tie Rod Sway Bar Wheel Bearning Hub For Dodge Ram 1500 1.Fit For: 2002-2005 Dodge Ram 1500 2.Package Includes: 2x Front Wheel Hub Bearing -513208 2x Front Sway Bar End Link -K80501 2x Rear Sway Bar End Link -K80425 2x Front Lower Ball Joint -K500153 1x Front Lower Control Arm - Passenger Side -K640446 1x Front Lower Control Arm - Driver Side -K640447 3.Note Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts. 1 Year Warranty Please check above compatibility list to make sure it fits your vehicle. Ball Joint Ball joints may be grouped into two classifications, load carrying and non-load carrying. Ball joints may be manufactured with forged, stamped, cold-formed, or screw-machined housings. The coil spring is seated on the control arm to which the load-carrying ball joint is attached. For example, when the coil spring is mounted between the lower control arm and the chassis, the lower ball joint is a load-carrying joint. In a torsion bar suspension, the load-carrying ball joint is mounted on the control arm to which the torsion bar is attached. A load-carrying ball joint supports the vehicle weight. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Frequently Asked Questions (1).How will I know that I have to renew my ball joint parts? Or replace them? If your ball joint fails, you will listen to a strange sound while driving. And that sound may help you to realize that your ball joint has failed and you have to renew them. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).Are worn ball joints dangerous? Yes, it can be quite dangerous. Because, a worn ball joint causes suspension damage, inspection failure, and breakage of related parts. It might make your front suspension come apart while driving, so the wheels move in whatever direction inertia takes them. That can lead to a fatal accident. (4).What happens if I don't replace ball joints? If you don't want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (5).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. Item Specifics Brand : cfspeed-autoparts Manufacturer Part Number : C84134801CPS Interchange Part Number : 515072,K7411,K7424,ES3538,K7422 OE/OEM Part Number : Suspension arm Kit,replacing control arm car,rods ends Superseded Part Number : car tie rod replacement Manufacturer Warranty : 10 Year Placement on Vehicle : Front Lower Upper Outer Type : Control Arm & Ball Joint Assembly Universal Fitment : No Features : Greasable Items Included : Mounting Hardware Performance Part : No Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On Finish : Coated Bolt Circle Diameter : 5.5In. Payment Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay. Shipping Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries. All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days. We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if it is different from the one in eBay. The tracking number will be given for the customer to check the shipping status online (registered or faster service only). We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout. Returns MoneyBackOrExchange We stand behind every product we sell. All of our brand new items come with a 30-Days money-back guarantee. We define the item as defective only if it doesn't function as described. It is the buyer's responsibility to understand the item description before bidding. Contact Us We are dedicated to provide high quality products and satisfied customer service to our sincerely customers, so if there's any questions or problems with our products or service, feel free to contact us please. All rights reserved.