1PCS Wheel Hub Bearing Rear For Jeep Grand Cherokee 2005-2010 Commander 2006-10

Description

Features: 100% Brand New in Box Fits LH (Driver Side) or RH (Passenger Side) Rear Fits 5 Lugs Wheels ABS Type:ABS with Tone Ring Sensor Wheel Studs Already Installed Brand New Wheel Hub Assembly Direct Replacement Built To Strict Quality Control Standards Replaces Dealer Part Numbers:712302, 512302, 29512302, 102123, BR930461, H512302, HA590141, WA512302, WE61080, 1411-246636, 730-0014 Fitments: Fits Jeep Commander 2006-2010 W/ ABS Models Fits Jeep Grand Cherokee 2005-2010 W/ ABS Models Please Notes: 1PCS Wheel Hub Bearing Rear For Jeep Grand Cherokee 2005-2010 Commander 2006-10 Features: 100% Brand New in Box Fits LH (Driver Side) or RH (Passenger Side) Rear Fits 5 Lugs Wheels ABS Type: ABS with Tone Ring Sensor Wheel Studs Already Installed Brand New Wheel Hub Assembly Direct Replacement Built To Strict Quality Control Standards Replaces Dealer Part Numbers: 712302, 512302, 29512302, 102123, BR930461, H512302, HA590141, WA512302, WE61080, 1411-246636, 730-0014 Fitments: Fits Jeep Commander 2006-2010 W/ ABS Models Fits Jeep Grand Cherokee 2005-2010 W/ ABS Models Please Notes: This Wheel Hub Bearing Will Only Work Properly On Vehicles With These Exact Options. If Your Vehicle Does Not Have The Options Listed, T his Mirror M ay Not Function Properly. Item Include: 1PCS Wheel Hub Bearing LH (Driver Side) or RH (Passenger Side) Rear Cotter Pin Nut Retainer Wheel Hub Lock Nut Hub Bolt Splash Guard Steering Knuckle Removal: Remove the bolt (1) and separate the front wheel sensor from the steering knuckle.? Remove brake caliper torque member bolts, leaving brake hose attached, reposition the caliper aside with wire. Put alignment marks (A) on disc brake rotor and wheel hub and bearing. Remove disc brake rotor. Remove cotter pin and the nut retainer,Loosen the wheel hub lock nut from the drive shaft using power tool. Using a piece of wood and a suitable tool, tap on the lock nut to disengage the drive shaft from the wheel hub and bearing. Remove the engine side cover. Remove the lower nut and bolt from the steering knuckle,Separate transverse link from steering knuckle. Separate drive shaft from wheel hub and bearing, Reposition the drive shaft aside with wire. Remove the wheel hub and bearing bolts using power tool. Remove the splash guard and the wheel hub and bearing from the steering knuckle. NOTE: Failure to separate the front wheel sensor from the steering knuckle may result in damage to the front wheel sensor; Pull out the front wheel sensor, being careful to turn it as little as possible. Do not pull on wheel sensorharness. Inspection after removel : Check components for deformationy,cracksy,and other damagey,and boots of transverse link ball joint for cracksy,axial end play,and swing torque. Installation: Installation is in the reverse order of the removal Caution: Do not reuse the wheel stud. Do not reuse the cotter pin. Place a washer (A) as shown to install the wheel studs (1) by using the tightening force of the nut (B). Clean the mating surfaces of the joint sub-assembly and the wheel hub and bearing. Apply lubricant to the surface (A) of the joint sub-assembly. Hold the wheel hub and bearing using a suitable tool. Tighten the wheel hub lock nut Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub lock nut. Do not use a power tool. Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the wheel hub lock nut to the specification. When installing a the cotter pin (1) and the nut retainer (2), securely bend the cotter pin to prevent rattles. Align the matching marks (A) on the disc brake rotor and on the wheel hub and bearing. Item Specifics Brand top-refitting Type Wheel Hub & Bearing Assembly Items Included As Picture Shown Manufacturer Warranty 1 Year Finish Polished,Rust Protected Performance Part No Universal Fitment No Vintage Car Part No Material Steel Wheel Stud Quantity 5 Placement on Vehicle Rear Manufacturer Part Number 11796774 OE/OEM Part Number 512302 Anti-lock Braking System Yes Brake Pilot Diameter 2.83 in. / 71.9 mm Flange Diameter 6.5 in. / 165 mm Quantity 1 Fitment type Direct Replacement ABS Type ABS with Tone Ring Sensor Wheel Pilot Diameter 2.81 in. / 71.4 mm Flange Shape Circle Flange Offset 2.5 in. / 63.5 mm Hub Pilot Diameter 3.34 in. / 84.9 mm Bolt Circle Diameter 5 in. / 127 mm Bolt Pattern 5 x 5 in (5 x 127 mm) Fitment 1 2006 2007 2008 2009 2010 Jeep Commander Wheel Studs Included Yes Flange Bolt Hole Quantity 4 Wheel Stud Size 1/2"-20 UNF Interchange Part Number 29512302, 102123, BR930461, WE61080, 1411-246636, 730-0014 Fitment 2 2005 2006 2007 2008 2009 2010 Jeep Grand Cherokee Spline Quantity 29 Knuckle Bolt Circle Diameter 4.69 in. / 119.2 mm Fitment Note W/ ABS Models Flange Bolt Size M12x1.75 Payment 1.We accept any payment which can be accepted by ebay. 2.If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 10 days as auction ended or order might be delayed. Shipping 1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 2. We only ship to confirmed order addresses. 3. The images shown are not the actual item and are for your reference only. 4. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service 5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back Returns 1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. to you as soon as possible with a reply. Our goal is customer satisfaction! Contact Us 1. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 2. It is impossible to address issues if we do not know about them! DESCRIPTION PAYMENT SHIPPING RETURN POLICY CONTACT US Shop Category Store Home Third Brake Light Assemblies Headlight Assembly Fog Light Side Marker Light Assemblies Mirror Assemblies Wheel Spacers AC Condenser Radiator Cooling Fan Wheel Bearing Hub Assembly Mass Air Flow Sensor Spoiler Wing Other Hot Item LED 3rd Tail Brake Light Cargo Light for 88-98 Chevy Silverado GMC Sierra Chrome USD 23.47 Black LED 3rd Tail Brake Light Cargo Light for 88-98 Chevy Silverado GMC Sierra USD 21.48 5 Smoke Cab Roof Running Marker Light Cover Lens For Ford F-250 F-350 Super Duty USD 10.87 For 07-13 Chevy Silverado 1500 2500HD 3500HD Chrome Smoke Third Brake Light USD 25.29 6pcs 4 Inch Round 24-LED Tail Light Reverse Backup Lamp Red For Truck Trailer USD 29.53 Picture New List Item For 2007-2013 Chevrolet Silverado 1500 2WD Front Wheel Bearing & Hub G Assembly USD 53.21 1PCS Automatic Locking Hub Front For 1999-2004 FORD F450 F350 F250 1C3Z-3B396-CB USD 61.64 2P Wheel Hub Bearings Front For 2006-2018 Toyota RAV4 3.5L Scion tC Manual Trans USD 61.21 1PCS Wheel Hub Bearing Rear FWD For Dodge Grand Caravan Chrysler Town & Country USD 48.17 2 Pcs Wheel Hub Bearings For Ford F-250 F-350 Super Duty SRW 2005-10 Front 4WD USD 180.08 Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us 1PCS Wheel Hub Bearing Rear For Jeep Grand Cherokee 2005-2010 Commander 2006-10 Features: 100% Brand New in Box Fits LH (Driver Side) or RH (Passenger Side) Rear Fits 5 Lugs Wheels ABS Type: ABS with Tone Ring Sensor Wheel Studs Already Installed Brand New Wheel Hub Assembly Direct Replacement Built To Strict Quality Control Standards Replaces Dealer Part Numbers: 712302, 512302, 29512302, 102123, BR930461, H512302, HA590141, WA512302, WE61080, 1411-246636, 730-0014 Fitments: Fits Jeep Commander 2006-2010 W/ ABS Models Fits Jeep Grand Cherokee 2005-2010 W/ ABS Models Please Notes: This Wheel Hub Bearing Will Only Work Properly On Vehicles With These Exact Options. If Your Vehicle Does Not Have The Options Listed, T his Mirror M ay Not Function Properly. Item Include: 1PCS Wheel Hub Bearing LH (Driver Side) or RH (Passenger Side) Rear Cotter Pin Nut Retainer Wheel Hub Lock Nut Hub Bolt Splash Guard Steering Knuckle Removal: Remove the bolt (1) and separate the front wheel sensor from the steering knuckle.? Remove brake caliper torque member bolts, leaving brake hose attached, reposition the caliper aside with wire. Put alignment marks (A) on disc brake rotor and wheel hub and bearing. Remove disc brake rotor. Remove cotter pin and the nut retainer,Loosen the wheel hub lock nut from the drive shaft using power tool. Using a piece of wood and a suitable tool, tap on the lock nut to disengage the drive shaft from the wheel hub and bearing. Remove the engine side cover. Remove the lower nut and bolt from the steering knuckle,Separate transverse link from steering knuckle. Separate drive shaft from wheel hub and bearing, Reposition the drive shaft aside with wire. Remove the wheel hub and bearing bolts using power tool. Remove the splash guard and the wheel hub and bearing from the steering knuckle. NOTE: Failure to separate the front wheel sensor from the steering knuckle may result in damage to the front wheel sensor; Pull out the front wheel sensor, being careful to turn it as little as possible. Do not pull on wheel sensorharness. Inspection after removel : Check components for deformationy,cracksy,and other damagey,and boots of transverse link ball joint for cracksy,axial end play,and swing torque. Installation: Installation is in the reverse order of the removal Caution: Do not reuse the wheel stud. Do not reuse the cotter pin. Place a washer (A) as shown to install the wheel studs (1) by using the tightening force of the nut (B). Clean the mating surfaces of the joint sub-assembly and the wheel hub and bearing. Apply lubricant to the surface (A) of the joint sub-assembly. Hold the wheel hub and bearing using a suitable tool. Tighten the wheel hub lock nut Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub lock nut. Do not use a power tool. Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the wheel hub lock nut to the specification. When installing a the cotter pin (1) and the nut retainer (2), securely bend the cotter pin to prevent rattles. Align the matching marks (A) on the disc brake rotor and on the wheel hub and bearing. Payment Shipping Returns Contact Us 1.We accept any payment which can be accepted by ebay. 2.If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 10 days as auction ended or order might be delayed. 1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 2. We only ship to confirmed order addresses. 3. The images shown are not the actual item and are for your reference only. 4. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service 5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back 1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. to you as soon as possible with a reply. Our goal is customer satisfaction! 1. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 2. It is impossible to address issues if we do not know about them! All rights reserved.