1PCS Wheel Hub Bearing W/ ABS Rear For Subaru Outback Legacy 2005-2009 2.5L 3.0L

Description

Features: 100% Brand New in Box Fits LH (Driver Side) or RH (Passenger Side) Rear Fits 5 Lugs Wheels ABS Type:Encoder Wheel Studs Already Installed Brand New Wheel Hub Assembly Direct Replacement Built To Strict Quality Control Standards Replaces Dealer Part Numbers:512293, 101909, H512293, WA512293, AX12293, 1411-09871, 051-6259, HA590119, BR930474, 760-0010, WE60998, 28473AG01A, 28473AG00B, 28473AG00A Fitments: Fits Subaru Legacy 2005-2009 Fits Subaru Outback 2005-2009 Please Notes: 1PCS Wheel Hub Bearing W/ ABS Rear For Subaru Outback Legacy 2005-2009 2.5L 3.0L Features: 100% Brand New in Box Fits LH (Driver Side) or RH (Passenger Side) Rear Fits 5 Lugs Wheels ABS Type: Encoder Wheel Studs Already Installed Brand New Wheel Hub Assembly Direct Replacement Built To Strict Quality Control Standards Replaces Dealer Part Numbers:512293, 101909, H512293, WA512293, AX12293, 1411-09871, 051-6259, HA590119, BR930474, 760-0010, WE60998, 28473AG01A, 28473AG00B, 28473AG00A Fitments: Fits Subaru Legacy 2005-2009 Fits Subaru Outback 2005-2009 Please Notes: This Wheel Hub Bearing Will Only Work Properly On Vehicles With These Exact Options. If Your Vehicle Does Not Have The Options Listed, T his Mirror M ay Not Function Properly. Item Include: 1PCS Wheel Hub Bearing LH (Driver Side) or RH (Passenger Side) Rear Cotter Pin Nut Retainer Wheel Hub Lock Nut Hub Bolt Splash Guard Steering Knuckle Removal: Remove the bolt (1) and separate the front wheel sensor from the steering knuckle.? Remove brake caliper torque member bolts, leaving brake hose attached, reposition the caliper aside with wire. Put alignment marks (A) on disc brake rotor and wheel hub and bearing. Remove disc brake rotor. Remove cotter pin and the nut retainer,Loosen the wheel hub lock nut from the drive shaft using power tool. Using a piece of wood and a suitable tool, tap on the lock nut to disengage the drive shaft from the wheel hub and bearing. Remove the engine side cover. Remove the lower nut and bolt from the steering knuckle,Separate transverse link from steering knuckle. Separate drive shaft from wheel hub and bearing, Reposition the drive shaft aside with wire. Remove the wheel hub and bearing bolts using power tool. Remove the splash guard and the wheel hub and bearing from the steering knuckle. NOTE: Failure to separate the front wheel sensor from the steering knuckle may result in damage to the front wheel sensor; Pull out the front wheel sensor, being careful to turn it as little as possible. Do not pull on wheel sensorharness. Inspection after removel : Check components for deformationy,cracksy,and other damagey,and boots of transverse link ball joint for cracksy,axial end play,and swing torque. Installation: Installation is in the reverse order of the removal Caution: Do not reuse the wheel stud. Do not reuse the cotter pin. Place a washer (A) as shown to install the wheel studs (1) by using the tightening force of the nut (B). Clean the mating surfaces of the joint sub-assembly and the wheel hub and bearing. Apply lubricant to the surface (A) of the joint sub-assembly. Hold the wheel hub and bearing using a suitable tool. Tighten the wheel hub lock nut Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub lock nut. Do not use a power tool. Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the wheel hub lock nut to the specification. When installing a the cotter pin (1) and the nut retainer (2), securely bend the cotter pin to prevent rattles. Align the matching marks (A) on the disc brake rotor and on the wheel hub and bearing. Item Specifics Brand top-refitting Type Wheel Hub & Bearing Assembly Items Included As Picture Shown Manufacturer Warranty 1 Year Finish Polished,Rust Protected Performance Part No Universal Fitment No Vintage Car Part No Material Steel Wheel Stud Quantity 5 Placement on Vehicle Rear Manufacturer Part Number 11824404 OE/OEM Part Number 512293 Anti-lock Braking System Yes Brake Pilot Diameter 2.28 in. / 57.9 mm Flange Diameter 4.88 in. / 124 mm Quantity 1 Fitment type Direct Replacement ABS Type Encoder Wheel Pilot Diameter 2.2 in. / 55.9 mm Flange Offset 2.57 in. / 65.4 mm Hub Pilot Diameter 3.31 in. / 84 mm Bolt Circle Diameter 3.94 in. / 100 mm Bolt Pattern 5 x 100 mm Fitment 1 2005 2006 2007 2008 2009 Subaru Outback Wheel Studs Included Yes Wheel Stud Size M12x1.25 Interchange Part Number 512293 WE60998 BR930474 HA590119 28473-AG00A WB12293 Bearing Generation G3 Fitment 2 2005 2006 2007 2008 2009 Subaru Legacy Knuckle Bolt Hole Size M12x1.25 Bearing Type Ball Bearing Knuckle Bolt Circle Diameter 4.21 in. / 107 mm Flange Bolts Included No Flange Bolt Hole Quantity 4 Flange Shape Rectangular Inside Spline Quantity 25 Payment 1.We accept any payment which can be accepted by ebay. 2.If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 10 days as auction ended or order might be delayed. Shipping 1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 2. We only ship to confirmed order addresses. 3. The images shown are not the actual item and are for your reference only. 4. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service 5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back Returns 1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. to you as soon as possible with a reply. Our goal is customer satisfaction! Contact Us 1. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 2. It is impossible to address issues if we do not know about them! DESCRIPTION PAYMENT SHIPPING RETURN POLICY CONTACT US Shop Category Store Home Third Brake Light Assemblies Headlight Assembly Fog Light Side Marker Light Assemblies Mirror Assemblies Wheel Spacers AC Condenser Radiator Cooling Fan Wheel Bearing Hub Assembly Mass Air Flow Sensor Spoiler Wing Other Hot Item 5 Smoke Cab Roof Running Marker Light Cover Lens For Ford F-250 F-350 Super Duty USD 10.87 Black LED 3rd Tail Brake Light Cargo Light for 88-98 Chevy Silverado GMC Sierra USD 21.48 6pcs 4 Inch Round 24-LED Tail Light Reverse Backup Lamp Red For Truck Trailer USD 29.53 For 07-13 Chevy Silverado 1500 2500HD 3500HD Chrome Smoke Third Brake Light USD 25.29 LED 3rd Tail Brake Light Cargo Light for 88-98 Chevy Silverado GMC Sierra Chrome USD 23.47 Picture New List Item 2PCS 1.5" Wheel Spacers 5x127 14x1.5 For 1995-1999 Chevy Tahoe GMC Yukon 2WD USD 45.73 2 Pcs 1" Wheel Adapters For Dodge Grand Caravan 5x127 to 5x114.3 5x5 to 5x4.5 USD 38.70 2 Pcs 1.5" Hub Centric Wheel Spacers 12x1.5 For Chevy S10 Camaro Corvette 5x4.75 USD 47.91 2 Pcs 1.5" Conversion Wheel Adapters 1/2"x20 For Ford Dodge to Jeep 5x5.5 to 5x5 USD 53.15 2 Pcs 1.5" Conversion Wheel Adapters For Chevy Silverado 2500 HD 8x6.5 to 8x180 USD 64.03 Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us 1PCS Wheel Hub Bearing W/ ABS Rear For Subaru Outback Legacy 2005-2009 2.5L 3.0L Features: 100% Brand New in Box Fits LH (Driver Side) or RH (Passenger Side) Rear Fits 5 Lugs Wheels ABS Type: Encoder Wheel Studs Already Installed Brand New Wheel Hub Assembly Direct Replacement Built To Strict Quality Control Standards Replaces Dealer Part Numbers:512293, 101909, H512293, WA512293, AX12293, 1411-09871, 051-6259, HA590119, BR930474, 760-0010, WE60998, 28473AG01A, 28473AG00B, 28473AG00A Fitments: Fits Subaru Legacy 2005-2009 Fits Subaru Outback 2005-2009 Please Notes: This Wheel Hub Bearing Will Only Work Properly On Vehicles With These Exact Options. If Your Vehicle Does Not Have The Options Listed, T his Mirror M ay Not Function Properly. Item Include: 1PCS Wheel Hub Bearing LH (Driver Side) or RH (Passenger Side) Rear Cotter Pin Nut Retainer Wheel Hub Lock Nut Hub Bolt Splash Guard Steering Knuckle Removal: Remove the bolt (1) and separate the front wheel sensor from the steering knuckle.? Remove brake caliper torque member bolts, leaving brake hose attached, reposition the caliper aside with wire. Put alignment marks (A) on disc brake rotor and wheel hub and bearing. Remove disc brake rotor. Remove cotter pin and the nut retainer,Loosen the wheel hub lock nut from the drive shaft using power tool. Using a piece of wood and a suitable tool, tap on the lock nut to disengage the drive shaft from the wheel hub and bearing. Remove the engine side cover. Remove the lower nut and bolt from the steering knuckle,Separate transverse link from steering knuckle. Separate drive shaft from wheel hub and bearing, Reposition the drive shaft aside with wire. Remove the wheel hub and bearing bolts using power tool. Remove the splash guard and the wheel hub and bearing from the steering knuckle. NOTE: Failure to separate the front wheel sensor from the steering knuckle may result in damage to the front wheel sensor; Pull out the front wheel sensor, being careful to turn it as little as possible. Do not pull on wheel sensorharness. Inspection after removel : Check components for deformationy,cracksy,and other damagey,and boots of transverse link ball joint for cracksy,axial end play,and swing torque. Installation: Installation is in the reverse order of the removal Caution: Do not reuse the wheel stud. Do not reuse the cotter pin. Place a washer (A) as shown to install the wheel studs (1) by using the tightening force of the nut (B). Clean the mating surfaces of the joint sub-assembly and the wheel hub and bearing. Apply lubricant to the surface (A) of the joint sub-assembly. Hold the wheel hub and bearing using a suitable tool. Tighten the wheel hub lock nut Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub lock nut. Do not use a power tool. Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the wheel hub lock nut to the specification. When installing a the cotter pin (1) and the nut retainer (2), securely bend the cotter pin to prevent rattles. Align the matching marks (A) on the disc brake rotor and on the wheel hub and bearing. Payment Shipping Returns Contact Us 1.We accept any payment which can be accepted by ebay. 2.If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 10 days as auction ended or order might be delayed. 1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 2. We only ship to confirmed order addresses. 3. The images shown are not the actual item and are for your reference only. 4. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service 5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back 1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. to you as soon as possible with a reply. Our goal is customer satisfaction! 1. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 2. It is impossible to address issues if we do not know about them! All rights reserved.