2Pcs Upper+Lower Oxygen Sensor For 2011-2014 Hyundai Elantra 1.8L Only fit Calif
$ 32.21
Description
2Pcs Upper+Lower Oxygen Sensor For 2011-2014 Hyundai Elantra 1.8L Only fit Calif. 2014 Hyundai Elantra (L4, 1.8L) (California Emission;SE; Sport). 2014 Hyundai Elantra (L4, 2.0L) (California Emission;GL; GLS; L; Limited; SE; Sport). 2014 Hyundai Elantra Coupe (L4, 2.0L) (California Emission;GL; GLS; GS; SE). Description Specification: This Oxygen O2 Sensor is a new, aftermarket replacement part that has the following specifications: Direct Fit Correct Connector No cutting or splicing Interchange Part Number: 234-5082,234-4552 Line length:350mm,620mm 4&5 wire configuration. Direct Plug-In Replacement. * Warranty: 2 Year Built and tested to strict quality control standards Fit Vehicles: 2011-2014 Hyundai Elantra (L4, 1.8L) (California Emission;GL; GLS; L; Limited) 2013 Hyundai Elantra Coupe (L4, 1.8L) (California Emission;GLS; GS; SE) 2013 Hyundai Elantra GT (L4, 1.8L) (California Emission;Base; GL; GLS; SE) 2014 Hyundai Elantra (L4, 1.8L) (California Emission;SE; Sport) 2014 Hyundai Elantra (L4, 2.0L) (California Emission;GL; GLS; L; Limited; SE; Sport) 2014 Hyundai Elantra Coupe (L4, 2.0L) (California Emission;GL; GLS; GS; SE) 2014 Hyundai Elantra GT (L4, 2.0L) (California Emission;Base) Package Include: 2 x Oxygen Sensor Features: Extensively Tested During Manufacture to Guarantee Quality and Reliability Supplied With a Factory-Fitted Connector for Easy Installation Precision manufactured with a sensing element incorporating premier technical ceramics Where are my oxygen sensors located? Diagnostic Trouble Codes (DTC) When oxygen sensor failure occurs, a DTC is recorded in the Engine Control Unit (ECU) and a Malfunction Indicator Lamp (MIL) is illuminated on the dash, alerting the driver the vehicle has a problem. How to replace an oxygen sensor? 1- Disconnect the battery. 2- Locate the sensor connector by following its wires. Disconnect it.? 3- Remove the sensor cable from its clips all along its way to the sensor. 4- A specific 22mm socket with side cut out exists (see below). You can use a spanner instead. Hold it in one hand and give it a firm hit with the other hand. It will then unscrew very easily. 5- Remove the sensor and fit the new one. 6- Re-route the cable carefully and meticulously and fix it at every clip. Reconnect the connector. 7- Reconnect the battery and wait 5 minutes before starting the engine. Please take a video clip of the voltmeter and contact us if our sensor: Goes above range between 0.1 and 0.9 volt Remains below 0.5 volts Stays fixed at a particular voltage You're free to choose replacement or refund if our sensor fails to work, in this case. Q: How do I know the O2 sensor is good or not? A: The only way to know if the O2 sensor is functioning normally is to check its responsiveness to changes in the air/fuel mixture, by Voltage Measurement or Waveform Simulation. Use a 10-megaohm digital voltmeter. Hook up the voltmeter's red probe to the sensor's signal wire and the black probe to engine ground. (Use back probe method, DO NOT pierce the wire.) For a good sensor, voltage should fluctuate constantly between 0.1 and 0.9 volts after starting the engine for 2 or 3 minutes. You're free to choose replacement or refund if our sensor fails to work, in this case.
