4x Front and Rear Shock Struts Assembly w/Coil Spring for Toyota Camry 2007-2011

Description

4x Front and Rear Shock Struts Assembly w/Coil Spring for Toyota Camry 2007-2011 Item Description 【High Quality】 100% brand new,Strictly produced according to the standard and the quality and stability of the product are better. 【Easy To Install】 Accurately locate the installation holes, reduce deviations, remove and replace the complete strut assembly without purchasing any other special installation tools 【Recover Performance】 Replacing our struts assembly, shorten the braking distance, and increase the safety distance,improve steering response, reduce stopping distance and give you more confidence in driving. 【Increase Tire Grip】 By increasing the spring stiffness coefficient, the rapid vibration of the wheel is suppressed, the tire is prevented from leaving the road, and the exercise stability is improved. 【Bounce Reduction】 Damping rods reduce body vibration and bounce by generating resistance through the flow of fluid to absorb or slow down the direct impact of energy. 【Kit includes】 2x Front Complete Struts w/Coil Spring Assembly - Replace Part Number 172307 172308, 2x Rear Complete Struts w/Coil Spring Assembly - Replace Part Number 172309 172310 【Vehicle Compatibility】 Please check the description and compatibility chart before your purchasing， if you have any question regarding our this product. Installation Step 1: Before You Lift the Vehicle, Loosen Lug Nuts One Full Turn. Step 2: Jack up Vehicle and Use Jack Stands for Safety & Remove the Tire from the Rotor. Step 3: (Wheel Alignment Is Necessary After Strut Replacement.) Marking the Position of All the Bolts Will Help Keep the Alignment Close to Original and save Time Aligning. Use a Colored Pencil to Mark the Old Strut on the Bolt. Step 4: Use Penetrating Oil (Such As Wd40) to Coat Any Rusted Fasteners, Let Soak for Approximately 1 Hour. Step 5: (Optional) While Waiting for Oil to Soak, Take This Time to Inspect All Other Components That May Need Replacement (Brake Pads, Rotors, Brake Hoses, Ball Joints, Cv Boots, Tie Rod Ends, Bushings, Sway Bars, Etc). Step 6: Remove Any Brake Line or Wire Attachments from the Strut Body. Do Not Disconnect Brake Lines (If Possible)! Opening Brake Lines Will Require Bleeding of the Brake System. Use Extreme Caution When Removing Brake Lines from Your Struts, As Any Damage to Your Brake Line Can Result in Expensive and Time Consuming Repairs. Step 7: Remove Sway bar Attached to the Strut Assembly or Control Arm. Step 8: Remove the Tie Rod (Only If It Attached to the Body of the Strut, If Not Leave It Attached to the Steering Knuckle). Step 9: Remove the Strut to Knuckle Bolts at the Bottom of the Strut. on some Vehicles, the Brake Caliper and Rotor May Need to Be Removed to Gain Access. Step 10: Remove the Upper Mounting Plate Bolts Located in the Engine or Trunk Compartment. Do Not Remove the Center Retaining Nut! It Is Not Safe to Unload the Spring from the Assembly in This Position. Step 11: Carefully Remove the Old Strut Assembly from the Vehicle. Be Very Cautious Not to Let the Strut "Drop" down on Your Brake Line, Rotor or Drum. Step 12: Install the New Complete Strut Assembly in the Reverse Order As Above (Steps 11-6). Using an Anti-seize Compound on All Fasteners Is Suggested. Step 13: Carefully Double Check Your Work and Make Sure Everything Is Tightened to Manufacturers Torque Specifications. Step 14: Replace the Tire the Rotor and Tighten to Manufacturers Torque Specifications. Step 15: Slowly Lower the Vehicle down After Removing the Jack Stands. Pay Very Close Attention to Any Odd Sounds When the Vehicle Is Lowered Onto the New Complete Strut Assemblies. Step 16: It Is Very Important That You Immediately "Road Test" Your Vehicle Right Away to Ensure That Installation Was Done Properly. Listen and Feel for Common Signs of Incorrect Installation While Driving Slowly over Speed Bumps, Rough Road or Potholes. Precautions for replacing the shock absorber: 1. When installing a new shock absorber, you should pay attention to whether the model matches, please pay attention to the matching model list before purchasing, and confirm whether the left and right are correct. 2. Check the quality status of the new shock absorber, such as whether there is oil leakage in the appearance, etc., pay special attention to the surface of the piston not to be bumped. 3. Professional tools must be used during installation, and the shock absorber must not be forcibly installed. 4. Pay attention to whether the installation position between the shock absorber and the body and the car is correct. 5. During the assembly process, be sure to protect the surface of the piston rod, and avoid using tools to pull the piston rod or bump or scratch the piston rod, otherwise the shock absorber will leak oil. 6. All nuts should be new and tightened according to the specified parameters of the vehicle to ensure that the tightening torque of the connection part meets the specified parameters of the vehicle. 7. When tightening the nuts of the connecting part, it should be carried out in the natural state of the tire and meet the specified parameters of the vehicle. Specifications Condition:100% Brand New Warranty: 90 Day Free Return:30 Day Color：Black Included Hardware：Nuts Mounting Hardware：Not Included Part Type：Strut & Coil Spring Assembly Fitment Type：Direct Replacement Package include: 2 Front +2 Rear Struts Shocks Assy Fitment Fit for Toyota Camry 2.4L 2007-2008 (CE, Hybrid, LE, XLE) Fit for Toyota Camry 2.4L 2009 (Base, Hybrid, LE, XLE) Fit for Toyota Camry 2.4L 2010-2011 (Hybrid) Fit for Toyota Camry 2.5L 2010-2011 (Base, LE, XLE) Please Double-Check that this is compatible with your vehicle. Replace Complete Strut NO#: 172307 172308 172309 172310 Package Included 1x Front Left Struts Assembly w/Coil Spring 1x Front Right Struts Assembly w/Coil Spring 1 x Rear Left Complete Struts Assembly 1 x Rear Right Complete Struts Assembly As pictures show FAQ: I purchased by mistake, how do I cancel the order? Please contact us ASAP. If the item has not been shipped out we can cancel the order for you. If the item was shipped out you can refuse the package and wait for the item to return to us. I received your item but it does not fit or is defective Please contact us so we can assist you on the matter. Buy with confidence Our quality is based on meeting the requirements of the manufacturer and improvement them in design problems manufacture. NOTE: (1)It would be highly appreciated if you might contact us first once you have any problems concerning the items. And you can expect all the issues would be resolved ASAP! (2)Please let us know before you send us the neutral/negative feedback that wont help to finish the issues. And I will definitely try my best to provide the best solutions which would meet our satisfactory! (3)According to the distance of the receipt address items would be sent from CA or NJ